Doing Things Wrong

Basses (3/4)

Audiovox 736 Replica Bass
Audiovox Gibson-style Bass
Audiovox Ukulele Bass
Audiovox Fretless Bass
Audiovox Danelectro-style Bass
Audiovox Electric Upright Bass
BC Rich "Osprey" Bass
Brownsville Violin Bass
Cowbell Bass
Danelectro Silvertone 1443 Bass
Danelectro Pro-1 Bass
Fender Jazzmaster Bass 1
Fender Jazzmaster Bass 2
Fender Jazzmaster Bass 3
Fender Stratocaster Bass 1
Fender Stratocaster Bass 2
Fender Stratocaster Micro Bass 2
Fender Stratocaster Micro Bass 1
Fender Stratocaster Fretless Bass
Fender Stratocaster Bass VI
Fender Stratocaster Uke Bass
Fender Stratocaster Bass IV
Fender Telecaster Bass
SX Precision Bass
Gibson Fenderbird Bass 1
Gibson Fenderbird Bass 2
Gibson Reverse Fenderbird Bass
Kubicki Bass
Mosrite Bass
Schwinn Stingray Bass
Rickenbacker 325 Bass 1
Rickenbacker 325 Bass 2
Rickenbacker 325 Bass 3
Rickenbacker 4001 Bass 1
 1 2 3 4  

These were my first two tries at a 325 bass. Both are plywood over pine hollow-bodies. The one on the left - #1 - used an experimental neck mounting that I didn't like. The one on the right - #2 - suffered a router mishap. I took all the good parts and built the solid-body, and both of these spent years on the scrap heap.


These were my first two tries at a 325 bass. Both are plywood over pine hollow-bodies. The one on the left - #1 - used an experimental neck mounting that I didn't like. The one on the right - #2 - suffered a router mishap. I took all the good parts and built the solid-body, and both of these bodies spent years on the scrap heap.


This was my third go at a 325 bass. The first one was unbalanced with this long neck, and the second suffered a router mishap. Eventually, I salvaged both of those, but first I took all the good parts and did this. Fender-type alder body with 3-tone sunburst, single binding. Surface-mounted pickups, active electronics. Finished entirely in polyurethane.


This one is kind of a joke and an experiment in just how cheap you can build a guitar. The body is dry-erase board over plywood - no finish - with Tolex side binding. Dry-erase board is Masonite covered with Melamine. The neck is 100% Radiata pine, even the fretboard. The "inlays" are glitter and CA glue. The pickguard is the other side of the dry-erase board - 'chalkboard'. The pickup mount is a 57 cent switch plate.


Danelectro Silvertone 1443 Bass
 
 
 
 

This is a project that took a long time, mainly due to the lacquer sunburst, which took several tries to get right. In the end, I even 'bursted the back of the neck. While it looks like an old Silvertone, it is actually thoroughly modern inside. 90's Danelectro lipstick pickups - the good ones, wired in series with a selector switch like they should be. 


This body was purchased on eBay from a parted-out guitar. Might have been a Squier, I don't remember. It was in pretty good shape, and I gave it a good polishing. The neck is hand-made, one of my first. The back is hand-picked Home Depot maple, the fretboard is pre-slotted rosewood from StewMac, I hadn't yet worked out how to make my own. If you cut the first two frets off a 34" fretboard, you end up with a 30" scale. That's about the limit with a pre-slotted fretboard though, as you start to run out of frets at the other end. The dots are 1/4" pearl from StewMac, expensive. The frets are probably pre-cut Fender.


This Strat bass is another of my early projects, an evolution of the first one. It uses basically the same neck, but mounted in the stock guitar neck pocket. This moves the bridge position adjacent to the old tremolo hole, but the expansive Mustang bridge plate covers it nicely. The pickguard looks stock, but is actually custom-made to cover the six stock bridge screw holes. If you can't get a Mustang bridge ( and you can't any more, ) you could extend the pickguard to cover all the guitar holes, or use a stock pickguard and just make a small bridge-sized cover. Or just leave the tremolo hole and keep your stash in it.


Uses the bottom four strings of a Bass VI set to get a low enough total string tension for the Strat tremolo to work.


The Fender Bass VI was a bass for guitarists. It was basically a Jazzmaster body with a 30" short-scale bass neck and six mid-weight strings tuned EADGBE one octave below a guitar, or the same as a bass. The string spacing is such that it can only be played with a pick. You can look up the rest of the details. Danelectro actually invented the Bass VI, they were always willing to try new things while Fender and Gibson were just determined to deepen the rut they were in. Rickenbacker's rut is so deep they can't even see out of it.


This fretless sounds really cool, and is super-easy to play, as you no longer have to stretch your hand unnaturally just to make ordinary patterns. It is set up with flats I found in the junk box. Can anyone tell me what kind of strings have blue thread leaders? The intonation fell right in, which is surprising considering the bridge was previously set up for 25.5" guitar strings. ( Actually, how important is intonation on a fretless anyway? )


Basses

 1 2 3 4  

Got the binding all scraped off on this one. No catastrophes, just a lap full of fine plastic shavings. You can see my homemade scraper. A bit of final touch-up to the stain, and this will be ready for a proper oil-based finish.

Printed from luthierylabs.com