Doing Things Wrong

A Decent Scroll Saw

General International 1.2 Amp 16 in. Variable Speed Scroll Saw with Flex Shaft LED Work Light

This is another piece that I got for free for review. Normally it is about $90. I would have soldiered on forever with my ancient Craftsman saw because I am cheap, but free is free and even better than cheap, and this is a nice upgrade. Compared to my antique model, this saw is variable speed, easier to change blades and takes both kinds, adds a work light, dust blower and dust port, and is lighter with a bigger table.

First, I noticed the blade was slightly out of kilter, which is not unexpected. I squared the table to the blade, and then adjusted the angle pointer to match. The table surface felt a little rough, so I smoothed it down with 1000 grit sandpaper, especially the edges. Finally, I removed the 'blade guard', which I really don't need. The dust blower and light are separate from the blade guard. The dust port is typical, whether it fits anything you have is pure chance, I wish there was a standard for these things, but there isn't.

Blade changes are easy with the included wrench, and the lower blade mount is easily visible through the table when you take out the insert. The blade wrench stores conveniently in a socket at the back of the saw. There is a little compartment at the side where you can store extra blades and the wrench for the blade guard. There is also a little tray where you can keep ready spare blades.

Radiata

Feature-wise, this saw is a big win over my ancient one. Variable speed is what I really wanted. The fixed-speed saw works fine on wood, but tends to melt plastic. Often, the plastic flows back together behind the blade and re-joins, and if you stop, it will solidify around the blade and you can throw the whole thing away, blade and all. This saw can slow down to 400 rpm, which is slow enough to cut even difficult clear plastics without overheating. The slow speeds are also nice if you are doing fine work and don't need a screaming banshee of a saw. At the other end of the speed scale, it cut 2 inch hard pine with little trouble and no bogging down, which my old saw was very prone to.

I noticed the instructions talk about oiling the arm bearings. My old saw has the same kind of bronze bushings, and I doubt they have ever been oiled or needed it; I have the old instructions and they make no mention of it. At any rate, putting few drops of oil on now and then is no big deal.

Looking at pictures, this saw is basically identical to a number of other brands. All these saws have identical major components, like the base casting, table, arm assembly, motor etc. They differ only in details like blade mount, knobs and color. Clearly all made to the same design in China, if not in the same factory. Compared to its siblings, this saw is lower-priced and superior in a number of details like the dust blower. If they were all next to each other, I would pick this one.

My one peeve is that the on/off switch is mounted sideways and out of sight below the table. It should be up and down, so you swipe up for on and down for off, like everything else. Sideways was a lot of fumbling, so I fixed it - the cover plate is plastic and I cut out the hole for the switch and re-mounted it. Then I closed up the openings with some scrap binding so it almost looks factory.


image

I took a drive over to Harbor Freight - purveyor of fine {sarcasm} Chinese tools & hardware - and picked up this little drill press. With a coupon, it cost me just over fifty bucks. This is not what I would call a good drill press, in fact, it is pretty crappy. The base and the table are stamped, not forged, and small. The quill travel is a measly two inches, parts that should be steel are aluminum, parts that should be aluminum are plastic, vibration is excessive, and the 3/8" chuck has a disconcerting wobble to it. I knew all that when I bought it, and I never would have if I did not already have a much better one, or at least a decent one. What I wanted from this drill press is small size and lightweight, so I can add it to my inside workstation, and not have to leave the heat/ac to go drill a hole in the garage. This press weighs well under 40 pounds and doesn't take up too much space on my inside workbench. My 'good' drill press is not something you'd want to move around a lot.

Printed from luthierylabs.com